500N Terminal Pull Force Tester for Cable Crimp Connections WPM-ADL-0.5KN
500N Terminal Pull Force Tester for Cable Crimp Connections WPM-ADL-0.5KN Thumb 500N Terminal Pull Force Tester for Cable Crimp Connections WPM-ADL-0.5KN Thumb
Video Thumbnail

500N Terminal Pull Force Tester for Cable Crimp Connections WPM-ADL-0.5KN

📅 2026-05-17 👁️ 2,131
  • Model No: WPM-ADL-0.5KN

  • Specifications

    500N Terminal Pull Force Tester for Cable Crimp Connections WPM-ADL-0.5KN
    Force Range: 500N (1000N optional)
    Resolution: 0.01N
    Accuracy: ±0.5%
    Power Supply: Nickel cyanide battery (220V AC charging 4-6 hours)
    Ambient Temperature: 0-60°C
    Ambient Humidity:
    Allowable Overload: 150%
    Dimensions: 115mm × 180mm × 30mm
  • Inquiry now

The WPM-ADL-0.5KN is a horizontal pull tester with a digital force gauge, built for crimp and weld connections on cable. Capacity is 500 N, with 1000 N available as an option, at 0.01 N resolution and ±0.5% accuracy. The gauge measures 115 x 180 x 30 mm and runs on a rechargeable battery charged from 220 V AC in 4 to 6 hours.

A crimp that has to be signed off needs a number, not a needle position. The sample is held between the clamp block on the left of the bed and the three-pin wire grip, the crank with the ball handle draws the sliding carriage away, and the gauge sits in the load path and holds the peak. Readings appear on the LCD, are entered on the keypad, and the ports at the end of the gauge take the data out to a PC. Allowable overload is 150%, so a pull that runs past 500 N does not end the gauge.

Against the WPM-490N the difference is resolution and record: the 490N reads 0 to 490 N on a dial, this unit resolves 0.01 N at ±0.5% and outputs the value. Where a series of pulls has to be logged against a crimp specification, this is the instrument; where a quick pass or fail at the bench is enough, the dial tester is simpler. Loads above hand-crank range go to the WPM-5000A motorised stand, which pulls at a set 15 to 240 mm/min.

Key Features

1. 500 N capacity, 1000 N optional, with 0.01 N resolution and ±0.5% accuracy.

2. 150% allowable overload, so a test that overshoots 500 N does not end the gauge.

3. Three-pin wire grip and a toggle clamp block hold the terminal and the wire end in line with the pull axis.

4. Crank with a ball handle drives the carriage by hand, and the gauge holds the peak for reading after release.

5. LCD and keypad on the gauge, with data ports at the end of the housing for transfer to a PC.

6. Battery powered with 220 V AC charging over 4-6 hours, so the tester can be used at a bench or at incoming inspection.

Technical Specifications

ParameterSpecification
ModelWPM-ADL-0.5KN
Machine typeHorizontal terminal pull force tester
Force range500 N (1000 N optional)
Resolution0.01 N
Accuracy±0.5%
Allowable overload150%
Power supplyBattery, 220 V AC charging 4-6 hours
Ambient temperature0-60 °C
Ambient humidityBelow 80%
Gauge dimensions115 x 180 x 30 mm

Applications

— Crimp pull test: terminal-to-wire pull force recorded against a crimp specification.

— Ultrasonic weld and splice: joint strength on harness splices.

— Connector retention: contact retention in housings and connector shells.

— Solder joint pull: lead-to-pad joints on connector boards checked to a set force.

— Incoming goods inspection: batch sampling of purchased crimped leads with the values logged.

Terminal Pull Force Tester WPM-ADL-0.5KN
Terminal Pull Force Tester WPM-ADL-0.5KN

Send us your question about this product

No file chosen
JPG / PNG / WebP, up to 10 MB each